IN THE EVENT OF TURBOCHARGER COMPRESSOR WHEEL FAILURE, ONE OR MORE OF THE FOUR CAPSCREWS THAT HOLD THE TURBOCHARGER TOGETHER MAY BE STRUCK BY PARTS OF THE COMPRESSOR WHEEL, RESULTING IN THE CAPSCREWS BEING DAMAGED. IF THESE CAPSCREWS ARE DAMAGED TO THE POINT THAT THEY ALLOW THE COMPRESSOR BACK PLATE TO DISLOCATE FROM THE TURBOCHARGER BEARING HOUSING, ENGINE LUBRICATING OIL MAY BE ALLOWED TO ESCAPE UNDER PRESSURE, CONTACTING THE ENGINE EXHAUST MANIFOLD SECTIONS OR TURBOCHARGER TURBINE HOUSING.
Manufacturer remedy
DEALER WILL INSTALL A SHIELD FOR THE HEADS OF THE FOUR CAPSCREWS, ALONG WITH STRONGER SAE 8 GRADE 8 CAPSCREWS, IF NECESSARY, AT NO COST TO OWNER.
Service brakes, air: antilock: interconnecting assembly(wiring)
Manufacturer
MACK TRUCKS, INCORPORATED
Vehicles affected
19,370
Reported to NHTSA
1978-10-03
Owners notified
1978-11-07
Defect description
DELAYS OF UP TO ABOUT 2 SECONDS MAY EXIST IN THE BRAKE APPLICATION TIMES TO THE BRAKES ON THE BOGIE AXLES IN THE PRESENCE OF CERTAIN TYPES OF WHEEL SPEED SENSOR SIGNAL DISCONTINUITIES OR DISTORTIONS THAT MAY OCCUR AS A RESULT OF SENSOR WIRE FAILURE. THIS CONSTITUTES A NON-COMPLIANCE TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS".
Manufacturer remedy
DEALER WILL INSTALL NEW WHEEL SPEED SENSORS THAT INCORPORATE IMPROVED WIRING AND THE PRESENT BOGIE ANTI-WHEEL LOCK SYSTEM WILL BE CHANGED TO AN AXLE-TO-AXLE SYSTEM FOR IMPROVED RELIABILITY.
Suspension: rear: springs: leaf spring assembly: hanger/bracket
Manufacturer
MACK TRUCKS, INCORPORATED
Vehicles affected
7,400
Reported to NHTSA
1977-11-21
Owners notified
1978-03-14
Defect description
A DEFICIENCY EXISTS IN THE WELDS SECURING THE REAR SPRING INSULATOR BRACKET TO THE AXLE HOUSING. THIS IS DUE TO IMPROPER POSITIONING OF THE WELD, IN RELATIONSHIP TO THE BRACKET AND AXLE HOUSING. FAILURE OF THE WELDS WOULD CAUSE SEPARATION OF THE SPRING INSULATOR BRACKET AND THE AXLE HOUSING, RESULTING IN IMPROPER ALIGNMENT OF THE AFFECTED AXLE.
Manufacturer remedy
DEALER WILL REWELD THE INSULATOR SPRING BRACKET AT NO COST TO OWNER.
THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEATBELT ASSEMBLIES". ALTHOUGH THE SEATBELTS IN QUESTION PERFORMED MARGINALLY WITH RESPECT TO THE 5000 LB. LOAD REQUIREMENT, ADDITIONAL TESTING CONFIRMED THAT THE ANCHOR COULD FAIL, ALLOWING EITHER THE ANCHOR TO SLIP OVER THE HOLD-DOWN NUT OR THE ANCHOR TO SEPARATE INTO TWO PIECES.
Manufacturer remedy
DEALER WILL INSPECT AND, IF NECESSARY, REPLACE SEAT BELT ASSEMBLIES WITHOUT CHARGE TO OWNER.
THE FLEX BLADE FANS ON THE INVOLVED VEHICLES MAY DEVELOP CRACKS IN THE LAMINATED STIFFENER AS A RESULT OF FATIGUE DURING OPERATION. IF SUCH A CONDITION EXISTS AND THE CRACKS GO UNDETECTED, CONTINUED OPERATION COULD CAUSE PIECES OF THE STIFFENER TO BREAK OFF.
Manufacturer remedy
DEALER WILL REPLACE THE ORIGINAL FAN WITH A STEEL FIXED BLADE FAN, FREE OF CHARGE.
THE FRONT WHEEL RIM CLAMP STUDS, INSTALLED ON THE INVOLVED VEHICLES, MAY NOT HAVE BEEN MANUFACTURED CORRECTLY, CAUSING A BRITTLE CONDITION IN THE THREAD ROOT AREA. THE STUDS COULD EVENTUALLY CRACK AND BREAK WHEN WHEEL NUTS ARE TIGHTENED TO SPECIFICATIONS.
Manufacturer remedy
THE DEALER WILL REPLACE ALL SUSPECT FRONT WHEEL STUDS, WITHOUT CHARGE TO OWNER.
Owner complaints
A complaint is one person's report to a federal agency. It is not a finding.
No complaints recorded for this model year.
Safety recall repairs are provided free of charge by franchised dealers, regardless of vehicle age or mileage. This page displays aggregated data for the model year. To check recall status for a specific vehicle, search its VIN at nhtsa.gov.