Altec Industries, Inc. (Altec) is recalling certain 2004-2023 DL42 and DL45 Digger Derricks. The incorrect hydraulic load holding valve may have been installed, which can cause the winch to lower uncontrollably and the load to fall.
Safety risk
An uncontrolled load falling increases the risk of injury to personnel or others nearby.
Manufacturer remedy
Altec will replace the load holding valve, free of charge. Owner notification letters are expected to be mailed October 6, 2023. Owners may contact Altec's customer service at 1-877-462-5832. Altec's number for this recall is MAB 3113.
Altec Industries Inc. (Altec) is recalling certain 2009-2019 DL/DM, DL/DMB, DH, D/2/3/4, and DC Digger Derrick vehicles. The slope indicator placard card may falsely indicate that the unit could be used without leveling on a 5 degree slope.
Safety risk
An operator may improperly set up the unit, making the unit unstable, thus increasing the risk of injury.
Manufacturer remedy
Altec will notify owners, and issue CSN 719 to owners, instructing them to remove the incorrect placards, free of charge. The recall began July 2, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 719.
Altec Industries, Inc (Altec) is recalling certain 2003-2019 Altec DL/DM, DL/DMB, and DC Digger Derrick vehicles. The pedestal tube welds may crack over time.
Safety risk
Unrepaired cracks may result in failure of the pedestal and uncontrolled movement increasing the risk of injury.
Manufacturer remedy
Altec will notify owners and will provide repairs as necessary and a reinforcing kit. The recall began April 3, 2019. Owners may contact Altec's customer service at 1-877-462-5832. Altec's number for this recall is CSN 713.
Electrical system: wiring: fuses and circuit breakers
Manufacturer
Altec Industries Inc.
Vehicles affected
331
Reported to NHTSA
2018-11-09
Owners notified
2019-01-09
Defect description
Altec Industries, Inc. (Altec) is recalling certain 2008-2018 Altec AC18, AC23, AC26, AC30 and AC38 Cranes and D2B, D3A, D4A/B, DL42B, DT65 and DT80 Digger Derrick vehicles. The wiring on the 12V circuit from the chassis battery to the Power Distribution Module (PDM) may be insufficiently sized.
Safety risk
The insufficiently sized wire may overheat, increasing the risk of fire.
Manufacturer remedy
Altec will notify owners, and dealers will replace the wiring to the PDM, with a larger wire and/or replace the circuit breaker, free of charge. The recall began January 9, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 703.
Altec Industries, Inc. (Altec) is recalling certain model year 2000-2013 Aerial Device and Digger Derrick trucks, equipped with Sure Power Battery Equalizers containing a particular epoxy sealing, aka 'potting', compound. The specific potting compound used in the subject products for insulation was found to be capable of conducting electricity after being exposed to heat.
Safety risk
Once electrically conductive, the material is capable of melting and burning, increasing the risk of a fire.
Manufacturer remedy
Altec will notify owners, and dealers will replace any affected battery equalizer, free of charge. The recall is expected to begin in September 2014. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 603.
Altec Industries Inc. (Altec) is recalling certain model year 2009-2013 DT80, and model year 2011-2013 D2, D3 and D4 digger derrick models manufactured June 2009 through November 2013. The fasteners that hold the bracket for the feeder tube (the telescopic hydraulic tube that supplies pump flow to the auger) may become loose allowing the feeder tube to fall.
Safety risk
A falling feeder tube increases the risk of injury to people nearby.
Manufacturer remedy
Altec will notify owners, and Altec service centers will install an upgraded feeder tube bracket and mounting hardware, free of charge. The recall began on February 19, 2014. Owners may contact Altec at 1-877-462-5832. Altec's number for this recall is CSN 591.
Altec Industries, Inc (Altec) is recalling certain model year 2007-2012 DC, and DL/DM Digger Derrick utility trucks, equipped with boom tip winches using Tulsa Winch Group (formerly Gear Products) winch drums. In the affected vehicles, the winch drum could deform or fracture.
Safety risk
If the winch fails while in use, it could cause personal injury.
Manufacturer remedy
Altec will notify owners and dealers will replace the winch drum, free of charge. The recall began on June 10, 2013. Altec's recall campaign number is CSN 574.
ALTEC IS RECALLING CERTAIN MODEL YEAR 2008 THROUGH 2011 UTILITY VEHICLES EQUIPPED WITH SURE POWER BATTERY SEPARATOR DEVICES, PART NUMBER 16511893 (MODEL 1314) OR 16512967 (MODEL 1315). THE BATTERY SEPARATOR CAN OVERHEAT.
Safety risk
OVERHEATING OF THE BATTERY SEPARATOR CAN RESULT IN SMOKE AND POSSIBLE FIRE.
Manufacturer remedy
ALTEC WILL NOTIFY OWNERS AND REPLACE THE BATTER SEPARATORS FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 11, 2012. OWNERS MAY CONTACT ALTEC AT 1-877-462-5832.
Owner complaints
A complaint is one person's report to a federal agency. It is not a finding.
No complaints recorded for this model year.
Safety recall repairs are provided free of charge by franchised dealers, regardless of vehicle age or mileage. This page displays aggregated data for the model year. To check recall status for a specific vehicle, search its VIN at nhtsa.gov.