Altec Industries Inc. (Altec) is recalling certain 2011-2025 Aerial Device, Digger Derrick, and 2022-2025 Service Body vehicles. The cable step wire rope assembly may be improperly secured, which can allow the cable entry step to detach from the vehicle.
Safety risk
A cable step that fails during use increases the risk of injury.
Manufacturer remedy
Altec will provide owners with instructions to inspect the cable crimps. If the cables are improperly crimped, Altec will provide instructions and a kit to replace the wire rope assemblies. Repairs will be performed free of charge. Owner notification letters were mailed October 24, 2025. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN-3246.
Altec Industries, Inc. (Altec) is recalling certain 2004-2023 DL42 and DL45 Digger Derricks. The incorrect hydraulic load holding valve may have been installed, which can cause the winch to lower uncontrollably and the load to fall.
Safety risk
An uncontrolled load falling increases the risk of injury to personnel or others nearby.
Manufacturer remedy
Altec will replace the load holding valve, free of charge. Owner notification letters are expected to be mailed October 6, 2023. Owners may contact Altec's customer service at 1-877-462-5832. Altec's number for this recall is MAB 3113.
Altec Industries Inc. (Altec) is recalling certain 2009-2019 DL/DM, DL/DMB, DH, D/2/3/4, and DC Digger Derrick vehicles. The slope indicator placard card may falsely indicate that the unit could be used without leveling on a 5 degree slope.
Safety risk
An operator may improperly set up the unit, making the unit unstable, thus increasing the risk of injury.
Manufacturer remedy
Altec will notify owners, and issue CSN 719 to owners, instructing them to remove the incorrect placards, free of charge. The recall began July 2, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 719.
Altec Industries, Inc (Altec) is recalling certain 2003-2019 Altec DL/DM, DL/DMB, and DC Digger Derrick vehicles. The pedestal tube welds may crack over time.
Safety risk
Unrepaired cracks may result in failure of the pedestal and uncontrolled movement increasing the risk of injury.
Manufacturer remedy
Altec will notify owners and will provide repairs as necessary and a reinforcing kit. The recall began April 3, 2019. Owners may contact Altec's customer service at 1-877-462-5832. Altec's number for this recall is CSN 713.
Electrical system: wiring: fuses and circuit breakers
Manufacturer
Altec Industries Inc.
Vehicles affected
331
Reported to NHTSA
2018-11-09
Owners notified
2019-01-09
Defect description
Altec Industries, Inc. (Altec) is recalling certain 2008-2018 Altec AC18, AC23, AC26, AC30 and AC38 Cranes and D2B, D3A, D4A/B, DL42B, DT65 and DT80 Digger Derrick vehicles. The wiring on the 12V circuit from the chassis battery to the Power Distribution Module (PDM) may be insufficiently sized.
Safety risk
The insufficiently sized wire may overheat, increasing the risk of fire.
Manufacturer remedy
Altec will notify owners, and dealers will replace the wiring to the PDM, with a larger wire and/or replace the circuit breaker, free of charge. The recall began January 9, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 703.
Altec Industries (Altec) is recalling certain 2014-2018 DHH and DHB Digger Derrick vehicles. The Zone Rating System may not alert the operator that the load being handled exceeds the rated load for the unit's specific position.
Safety risk
Without an alert, there is a greater risk of unit instability or a loss of load control, increasing the risk of injury.
Manufacturer remedy
Altec will notify owners and dealers will update the Zone Rating System software, free of charge. The recall began December 12, 2018. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 700.
Altec Industries Inc. (Altec) is recalling certain model year 2015-2016 Aerial Devices and Digger Derrick vehicles equipped with front bumper winches or capstans, manufactured December 26, 2015, to March 30, 2016. The affected vehicles have a hydraulic motor whose shaft may fail resulting in unexpected movement of the winch or the capstan.
Safety risk
Unexpected winch movement may increase the risk of injury.
Manufacturer remedy
Altec will notify owners, and dealers will replace the hydraulic motor, free of charge. The recall began on August 26, 2016, 2016. Owners may contact Altec customer service at 1-205-991-7733. Altec's number for this recall is CSN 635.
Altec Industries Inc. (Altec) is recalling certain model year 2014-2016 DL and DM Digger Derricks manufactured October 1, 2014, to April 30, 2016 with the digger booms mounted in the corner. The rotation bearing fasteners on the affected vehicles may not have been properly torqued.
Safety risk
If the fasteners are loose or improperly torqued, structural failure may result, causing unexpected movement of the digger derrick and increasing the risk of injury.
Manufacturer remedy
Altec has notified owners, and instruct them to perform the annual torque inspection, free of charge. The recall began June 2, 2016. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 633.
Owner complaints
A complaint is one person's report to a federal agency. It is not a finding.
No complaints recorded for this model year.
Safety recall repairs are provided free of charge by franchised dealers, regardless of vehicle age or mileage. This page displays aggregated data for the model year. To check recall status for a specific vehicle, search its VIN at nhtsa.gov.